SP Series Model PD

The UPS preference for traffic back-up in many states

SP Series Model PD Overview

Clary’s SP Series Model PD products feature an integrated PIM and programmable display. The SP Series Model PD are the world’s most advanced Uninterruptible Power Systems (UPS). Industry proven, SP Series Model PD systems provide clean, regulated double-conversion power for controllers and other sensitive equipment inside the cabinet, 100% of the time. Clary can provide systems which will sustain a continuous 1400/1800 watt load. Listed by many states as the preferred UPS system for traffic intersection back-up, Clary products are engineered to meet NEMA standards for traffic back-up systems with an operational temperature range of -40°C to +74°C. Clary SP Series are also designed to mount in existing traffic cabinets or in adjacent stand alone cabinets. Optional NEMA 3R Type II and Type III cabinets are available. Advanced communication features allow monitoring, configuration and control of the system over RS232, modem or network connections. See our SNMP Product Brochure. Available for both NEMA and 332 style cabinets.

SP Series Model PD Specifications

Voltage 120 VAC +12% (135 VAC), -25% (90 VAC) (before battery use)
Frequency 48 Hz to 62 Hz
Voltage 120 VAC ±3%
Frequency 50 Hz or 60 Hz
Current 10.4A
Crest Factor Ratio 50% load up to 4.8:1, 75% load up to 3.2:1, 100% load up to 2.4:1
THD 4.00% maximum
Dynamic Response ±4% for 100% step load change 0.5 ms recovery time
Overload 110% for 10 sec; 200% for 50 ms
UPS Protection Input and output short circuit; input and output overload; excessive battery discharge
Temperature -40°C to +74°C (-40°F to +165°F)
Humidity 0% to 95% non-condensing
Altitude Sea level to 10,000 ft
Input Hardwired to PIM
Outputs Hardwired to PIM, with single 15 Amp receptacle
Cabinet NEMA, 332 or CBO-123 cabinet style configurations available, NEMA, 3R Type II and Type III optional
Standard Features Power factor corrected input, Fully regenerative, True on-line continuous power, Low distortion sine wave output, Designed for non-linear loads, Extended brownout protection, EIA/RS232 data interface
Certifications FCC Class A, IEEE 587/ANSI C62.4, IEC 555@ 120 VA, NEMA
Typical Recharge Time to 85% Capacity @ 100% Load 48-72 hrs (more time required with extended battery option), < 20 hrs (with optional fast battery charger)
Ramping LEDs Single LEDs Battery level, Load level AC in, Inverter on, Low battery, Summary alarm, Alarm single LEDs, Alarm silence
Switches / Control Panel System power, Cold start, Test, Alarm silence, Event counter with reset, Hour meter, Battery disconnect
Audible Alarms Utility interrupt, Inverter failure, Overload, Low battery, Self test
Intelligent Computer Interfaces Serial interface for EIA 232, Optional NTCIP and TCP/IP via standard RJ45 connector, Full interactive remote computer monitoring and control of most features including load control (requires optional monitoring software), NTCIP and TCP/IP ready
Contact Closures "D" connector, Open collector (see user manual for additional interface information)
Model VA Watts Input Current Output Current Rating Backup Time* 100% / 50% Load Weight (lb) Rackmount H x W x D (in)
SP 2400PD-N/R 2400 1800 18.0A 20.0A 2400 VA / 1800 W 1.0 hours / 3.5 hours 28 6.0 x 19.0 x 10.0
SP 2000PD-N/R 2000 1400 14.3A 16.7A 2000 VA / 1400 W 1.0 hours / 3.5 hours 28 6.0 x 19.0 x 10.0
SP 1250PD-N/R Plus 1250 875 8.8A 10.4A 1250 VA / 875 W or 1400 W for 10 seconds 2.0 hours / 4.0 hours 27 6.0 x 19.0 x 10.0
SP 1250PD-N/R 1250 875 8.8A 10.4A 1250 VA / 875 W 2.0 hours / 4.0 hours 27 6.0 x 19.0 x 10.0

* Backup time is based on 41Ahr batteries


Contact us to learn more about our innovative products!
Contact Us