S 1500-601

UPS system built for medical devices, especially those that touch the patient

S 1500-601 Overview

The S1500-601 is a medical grade UPS system designed specifically for medical applications, with on-line technology that conditions and regenerates power 100% of the time. Engineered to meet UL listing 60601-1, it is proven to work when the power fails. The S1500-601 supports 1500VA or 1050 watts of load for 7 minutes of back-up time, and also supports either 120Vac or 230Vac input auto selecting, in fact, it will support input voltages as low as 96Vac and as high as 264Vac. Output voltage is 120Vac. This is a very low leakage unit that supports devices that directly contact the patient. The S1500-601 also supports input from generator power, and because the S1500-601 is an on-line unit it protects the devices connected to it by eliminating electrical anomalies that harm or destroy costly equipment.

S 1500-601 Specifications

Voltage 120 VAC +12%, -25% (without battery discharge)
Frequency 45 Hz to 65 Hz
Current 10.7 A
Voltage 120 VAC ±3%
Frequency Software selectable to sync with input utility or run at crystal controlled 50/60 Hz ±1 Hz
Current 12.5 A
Rating 1500 VA / 1050 W
Crest Factor Ratio 50% load up to 4.8:1, 75% load up to 3.2:1, 100% load up to 2.4:1
THD 3.00% maximum (linear), 5.00% maximum (non-linear)
Dynamic Response ±4% for 100% step load change 0.5 ms recovery time
Overload 110% for 10 sec; 200% for 50 ms
UPS Protection Input and output short circuit, Input and output overload, Excessive battery discharge
Temperature 0°C to +50°C (+32°F to +122°F)
Humidity 0% to 95% non-condensing
Altitude Sea level to 10,000 ft
Noise Level 39 dBA to 42 dBA at 5 ft
Input NEMA 5-15P plug with 6 ft cord (1000 - 1500 VA connectors), NEMA 5-20P plug on 6 ft cord (2000 - 2400 VA connectors)
Outputs Duplex hospital grade receptacle 5-15R, 1.25K-1.5K - 5-20R, 2K-2.4K
Weight (lb) 80
Standard Features Power factor corrected input, Fully regenerative, True on-line continuous power, Low distortion sine wave output, Designed for non-linear loads, Extended brownout protection, RS232 data interface, Inverter powers load continuously, Continuous operation on -25% to +12% utility without draining batteries, Automatic bypass, AC output (2 channel load control), Rear mounted ground stud
Certifications FCC Class A, IEEE 587/ANSI C62.4, IEC 555@ 120 VA, UL 1778, UL-60601-1
MTBF Inverter: > 100,000 hrs
Typical Recharge Time
(to 85% Capacity @ 100% Load)		 8 hrs (more time required with extended battery option)
Visual Indicators Battery level, Load level, AC in, Inverter on, Summary alarm, Alarm silence, Load on
Switches / Control Panel System power, Cold start, Load II, Test, Alarm silence
Audible Alarms Utility interrupt, Inverter failure, Overload, Low battery, Self test
Intelligent Computer Interfaces RS232 data interface (DB-9), Full interactive remote computer monitoring and control of most features including load control (requires optional monitoring software), Compatible with Systems Enhancement™ UPS control software
Contact Closures DB-9, Open collector, Optional dry contact module
SNMP Interface Allows full control and monitoring interface over network connection. Compatible with HP Openview™, IBM Netview™, CA Unicenter TNG™, and other major software offerings.
Contact us to learn more about our innovative products!
Contact Us